NOTE: Contractor Packs may be removed from retail box and shipped as 4 loose quarts due to recent regulation changes. These changes will only effect Los Angeles, San Bernardino, Riverside and Orange County in the state of California.
511 Impregnator is the original penetrating sealer designed for the protection of all medium to dense porous surfaces. 511 Impregnator forms an invisible barrier that is resistant to moisture and stains while allowing vapor to escape. 511 Impregnator is not a surface coating and will not alter the natural look. All surfaces treated are harder and less slippery.
NOTE: Contractor Packs may be removed from retail box and shipped as 4 loose quarts due to recent regulation changes. These changes will only effect Los Angeles, San Bernardino, Riverside and Orange County in the state of California.
511 Impregnator is the original penetrating sealer designed for the protection of all medium to dense porous surfaces. 511 Impregnator forms an invisible barrier that is resistant to moisture and stains while allowing vapor to escape. 511 Impregnator is not a surface coating and will not alter the natural look. All surfaces treated are harder and less slippery.
|
WATER, STAIN & SLIP PROTECTION FOR:
|
|
• Sanded Grout
• Quarry Tile
• Ceramic Tile
• Glazed Tile
|
• Porcelain Tile
• Polished Granite
• Polished Marble
• Terrazzo |
• Concrete
• Brick
• Stucco
• Slate |
• Quartz
• Travertine
• Agglomerate |
| SPECIAL FEATURES: |
|
|
• Interior & Exterior Use
• Weather Resistant
• Less Expensive
• OK for Food Areas
|
• Superior Coverage
• Easy to Use
• U.V. Transparent |
Coverage: 1,000 - 4,000 square feet per gallon (90 - 364 square meters per 3.785 liters).
Container sizes: Contractor Pak, quart, pint.
511 Impregnator meets V.O.C. requirements.
APPLICATION:
Read entire label and PDS/MSDS before using. 511 Impregnator should not be diluted or thinned in any way. 511 Impregnator should be used as is direct from approved container.
Before Grouting: Apply 511 Impregnator to all surfaces prior to grouting. This step will allow quick and easy cleanup after grouting. Grout can stain many surfaces if this procedure is not used prior to the grouting process. Apply 511 Impregnator using a Mira Brush or a clean towel. Apply enough to wet the surface. (See coverage charts) Be careful not to saturate the open grout joints. Allow 511 Impregnator to stand for
approximately 3 - 5 minutes for maximum penetration. All excess must be removed at this time by buffing surface with a clean dry towel. This is very important on polished, glazed and porcelain surfaces. Allow 511 Impregnator to cure for 6 - 12 hours before continuing with the grouting procedure.
After Grouting: Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to cure per manufacturers specification. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner , (GCFR) Grout & Concrete Film Remover (Hydrochloric Acid), Sulfamic Acid Crystals or Epoxy Grout Film Remover following the instructions carefully. Once the area has completely dried, proceed with the sealing of the grout for water and stain resistance. Apply 511 Impregnator to all grout with a paint brush. Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries. On larger jobs grout can be sealed by retreating the entire area including the tile or stone surface a second time. Be careful not to allow the sealer to puddle or dry on presealed surfaces.
Existing Installation- Application instructions:
Surface must be dry and free of contaminants, including previously applied sealers, dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime. Surface Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira Strip or H2O Strip as directed. Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust, grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover) Phosphoric Acid Cleaner as directed. For a non acid deep clean use Liquid Poultice as directed. Light Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Mira Soap, Counter Kleen as directed.
Follow the application instructions previously mentioned, except now, seal the grout and tile or stone surfaces at the same time. When treating surfaces together, make sure that the recessed grout is saturated.
Manufacturer: N/A
SKU: 30.10114
UPC: 753927513619
Sign In
